Onkyo TX NR609 No Sound [100% Solved]

by

In 1946, Onkyo started producing phonograph pickups. The company is still producing audio components as of 2010. Onkyo’s receivers are popular for allowing other stereo or home theatre components to work together to provide you with a full listening and viewing entertainment experience. If the receiver that controls your home theatre or stereo system is malfunctioning, it will not work properly. With an Onkyo receiver, you will run into several issues.

Incorrect settings on your Onkyo receiver  results in no sound. The digital input signal should be set to “Auto.” Select the correct digital input source. Adjust the volume controls so you can hear sound. The bare wires of the speakers should be in contact with the metal parts of the speaker terminal on the receiver

Your Onkyo receiver’s settings are likely wrong, resulting in no tone. The “Auto” setting for the digital input signal should be used. Choose the proper digital input source. To hear music, adjust the volume controls. The metal parts of the speaker terminal on the receiver should be in contact with the bare wires of the speakers. Your Onkyo receiver’s settings are likely wrong, resulting in no tone.

Quick Navigation

How to Reset the Onkyo TX NR609 7.2 HDMI

 Home Theater Surround Receiver to Factory Settings Press and hold the VCR/DVR button, otherwise the On/Off button, until the monitor reads “clear,” and the receiver will be factory reset.

How to Troubleshoot Onkyo Receivers

These problems can be detected and corrected.

1st step

If the power won’t come on, plug the receiver into the wall. The appearance of lights on the front of the unit means that the power supply is functioning properly. If the Onkyo still won’t turn on, make sure the wall outlet is working. Try another device in the same outlet to see how it works.

Step 2 

If there is no sound, make sure the sources are connected and switched on. Since Onkyo receivers have an amplifier as well as a broadcast radio receiver, you can isolate the receiver by changing the “Source” to “FM Radio” and listening for noise. If you can’t hear something while tuning for stations, the problem may be with your speaker connections; double-check them. If you hear noise, the source, such as a DVD player, is to blame; check for power and connections.

Step 3

If audio or video does not appear on television connected with an HDMI (High Definition Multimedia Interface) cable, check the settings on the Onkyo receiver. Choose “HDMI” from the “Monitor Out” options.

Step 4

If the problem persists, reset the Onkyo. The receiver can reach “Standby” if you hold down the “VCR/DVD” button when pressing the “On/Standby” button. Click the “On/Standby” button to turn it back on. Bear in mind that this would delete all defaults and other settings, so those are likely the ones causing the issues.

Problems With Onkyo Receivers

In 1946, Onkyo started producing phonograph pickups. The company is still manufacturing audio components as of 2010. Onkyo’s receivers are known for allowing other stereo or home theatre components to work together to provide you with a full listening and viewing entertainment experience. If the receiver that controls your home theatre or stereo system is malfunctioning, it will not work properly. With an Onkyo receiver, you will run into several issues.

There is no sound.

Your Onkyo receiver’s settings may be incorrect, resulting in no sound. The “Auto” setting for the digital input signal should be used. Choose the required digital input source. When using your machine with external speakers, unplug the headphones from the receiver. Unmute your Onkyo receiver by pressing the “Muting” button on the remote control. Check the inputs and outputs to make sure they’re connected to the receiver correctly. To hear music, adjust the volume controls. The metal portions of the speaker terminal on the receiver should be in contact with the bare wires of the speakers. Check for shorts in both speaker wire and power cords. Your Onkyo receiver can’t link to the internet on its own.

There is no image available.

Before you can see a frame, the video connections going into your Onkyo receiver must be firmly seated in the video inputs. Make sure you’re using the right cables, like S-Video or HDMI. Set your television to the same video input as the Onkyo receiver. Consult the owner’s manual for your television. If the receiver is set to a resolution that the TV does not support, no video will be output via the HDMI connections. A “Resolution Error” message will appear on the Onkyo receiver. To solve the dilemma, use a resolution setting that your TV supports.

Other Components Are Uncontrollable

The other components in your stereo or home theatre system are regulated by your Onkyo receiver. For the receiver to monitor the system, the settings on the receiver and the components must be identical. The R1 cable and the analog audio cable must be wired simultaneously. For the part, you’re trying to control, enter the necessary remote control code. Guide the remote control towards the receiver. Manually change the part if necessary. If the manual adjustment doesn’t work, replace the remote control’s batteries.

A recording is not possible.

When the proper settings are used on the recording part, the Onkyo receiver can only monitor the recording feature. Ascertain that the recording part is properly connected to the receiver. To prevent receiver harm, input signals are not fed through to outputs with the same name class as the receiver, such as DVR/In and DVR/Out. With the remote control, switch on the recording part. Make sure it’s set to “Record.” Adjust your system’s listening mode to “Pure Audio.” This mode does not allow you to record video.

Tx-nr609 no sound is not working

  • Make sure the MUTE feature isn’t switched on.
  • Increase the volume on your monitor.
  • Make sure there are no headphones plugged in.
  • Check to see if the problem affects any other devices connected to the TV. You might try changing the channel on the television or watching a movie on a DVD player.
  • To make sure this isn’t a bad set of cables, try different cables.
  • Changing the Surround Sound mode on the Audio/Video (A/V) receiver can help.

NOTE: Make sure the source you’re using supports Surround Sound audio. If not, using a Surround Sound setting can make it difficult to hear the audio. When playing a source that isn’t encoded with a Surround Sound signal, switch off Surround Sound.

If a BD/DVD player attached to an HDMI IN does not produce sound, check the BD/DVD player’s output settings and ensure that a supported audio format is selected.

Check the connected device’s digital audio output mode. The default setting on certain game consoles, such as those that support DVDs, is off.

  • You must pick an audio output device from a menu on some DVD-Video discs.
  • You’ll need an MC head amp or an MC transformer if your turntable uses an MC cartridge.
  • Make sure none of the connecting cables are twisted, bent, or broken.
  • Both speakers are not used in all listening modes
  • Set the speaker distances and adjust each speaker individually.
  • If you don’t want to listen to Pure Audio, don’t pick it (European, Australian and Asian models)
  • Although Zone 2 is active, the Pure Audio listening mode cannot be selected
  • I’m unable to pick a preferred listening mode.
  • Some listening modes may not be available depending on the speaker’s connection status. Check out the “Using the Listening Modes” section for more details.
  • Playing 5.1ch is not possible.
  • Please ensure the speakers are in good working order.
  • Both speakers are not used in all listening modes.
  • The speaker volume cannot be adjusted to the desired level
  • Look to see if a volume limit has been set.
  • There is a lot of noise.
  • Bundling analog audio (RCA) cables with power cords and speaker cabling with cable links
  • You cannot hear any sound if you turn your player from DTS to PCM because the unit does not switch formats immediately. In this scenario, you can pause your player for about 3 seconds before restarting it.

CONCLUSION

Even if your CD or LD player is connected to a digital input on the AV receiver, some CD and LD players may not be able to play DTS material properly. This is typical because the DTS bitstream has been altered (for example, the output speed, sampling rate, or frequency response) and the AV receiver no longer recognizes it as a genuine DTS signal. You can hear noise in such circumstances.

Using the pause, fast forward, or fast reverse functions on the y-axis to play DTS program content. The most common solution of the error is to reset your devices. This is the most easy and best way to solve such issues without making any efforts. This will save your time and money